masqmail

annotate INSTALL @ 206:0241aaccfcdb

find changesets by author, revision, files, or words in the commit message
default listen_addresses: use 127.0.0.1 instead of `localhost' because `localhost' could be bound to some other IP address. This is unlikely but could be. Using 127.0.0.1 is more safe. See mailing list for details
author meillo@marmaro.de
date Sat, 17 Jul 2010 00:34:40 +0200
parents 4fd237550525
children cab46cefa4ce
rev   line source
meillo@59 1 Additional information may be available in docs/ or on the website.
meillo@174 2 For installing on GNU/Linux distributions read docs/INSTALL.linux.
meillo@0 3
meillo@59 4
meillo@59 5 Installation instructions
meillo@59 6 -------------------------
meillo@59 7
meillo@165 8 To compile masqmail you need glib (>= 1.2) (http://www.gtk.org). Your
meillo@181 9 distribution probably provides it. Glib-2.0 works out of the box, for
meillo@181 10 glib-1.2, you need to adjust configure.ac. See the comment in there.
meillo@0 11
meillo@165 12 You need a user and a group for masqmail to run. If
meillo@165 13
meillo@165 14 grep '^mail:' /etc/passwd
meillo@165 15 grep '^trusted:' /etc/group
meillo@165 16
meillo@165 17 shows that the user `mail' and the group `trusted' exist, it's
meillo@165 18 probably best to use these. If they don't exist, create them:
meillo@0 19
meillo@59 20 groupadd -g 42 trusted
meillo@194 21 useradd -u 23 -g trusted -d /nonexistent -s /bin/false -c "masqmail MTA" mail
meillo@0 22
meillo@165 23 If you use other names than `mail' and `trusted' use the options
meillo@165 24 described below for configure. The 23 and 42 are just a suggestion,
meillo@165 25 you can use any (not yet used) number you like, but preferably one
meillo@165 26 lower than 100. It does not have to be the same for the user `mail'
meillo@165 27 and the group `trusted'.
meillo@165 28
meillo@0 29
meillo@174 30 Compiling is a matter of the usual procedure. In the source directory,
meillo@59 31 after unpacking do:
meillo@0 32
meillo@59 33 ./configure
meillo@59 34 make
meillo@59 35 make install
meillo@0 36
meillo@0 37
meillo@0 38
meillo@59 39 Additional options for configure
meillo@59 40 --------------------------------
meillo@0 41
meillo@59 42 See the output of
meillo@0 43
meillo@59 44 ./configure -h
meillo@0 45
meillo@165 46 Here is a selection of the options with additional explanations:
meillo@0 47
meillo@165 48 --with-user=USER
meillo@165 49 sets the user as which masqmail will run. Default is 'mail'. USER has
meillo@165 50 to exist before you 'make install'.
meillo@0 51
meillo@165 52 --with-group=GROUP
meillo@165 53 sets the group as which masqmail will run. Default is 'trusted'. GROUP
meillo@165 54 has to exist before you 'make install'.
meillo@0 55
meillo@0 56
meillo@165 57 --with-logdir=LOGDIR
meillo@165 58 sets the directory where masqmail stores its log files. It will be
meillo@165 59 created if it does not exist. Default is /var/log/masqmail/.
meillo@0 60
meillo@165 61 --with-spooldir=SPOOLDIR
meillo@165 62 sets the directory where masqmail stores its spool files. It will be
meillo@165 63 created if it does not exist. Default is /var/spool/masqmail/.
meillo@0 64
meillo@165 65 --with-confdir=CONFDIR
meillo@165 66 sets the default configuration directory to CONFDIR, in case you
meillo@165 67 prefer another location than /etc/masqmail/.
meillo@0 68
meillo@0 69
meillo@165 70 --enable-auth
meillo@165 71 enables ESMTP AUTH support (disabled by default)
meillo@0 72
meillo@165 73 --enable-ident
meillo@175 74 enables RFC 1413 support. If you have the libident dynamic library
meillo@165 75 installed, this will be linked, otherwise it will be statically linked
meillo@165 76 using the sources included in the package.
meillo@0 77
meillo@165 78 --disable-resolver
meillo@175 79 disables resolver support. Without the resolver functions, masqmail
meillo@165 80 uses only gethostbyname() to resolve DNS names, and you cannot send
meillo@165 81 mail without a smart host. Not recommended.
meillo@0 82
meillo@165 83
meillo@165 84 --with-libcryto
meillo@165 85 instead of using the md5 and hmac functions within the package, link
meillo@192 86 dynamically with libcrypto. This applies only if you have SMTP AUTH
meillo@192 87 enabled. Only makes sense if your resources are limited and you have
meillo@192 88 libcrypto installed. Untested.
meillo@165 89
meillo@0 90
meillo@165 91 --disable-debug
meillo@175 92 disables debugging; setting it on the command line or in the
meillo@175 93 configuration has no effect. Strongly discouraged, since you miss
meillo@175 94 valuable information if something goes wrong.
meillo@0 95
meillo@59 96
meillo@59 97
meillo@165 98 Checking the installation
meillo@165 99 -------------------------
meillo@0 100
meillo@0 101 Check that 'make install' worked correctly. The following command:
meillo@0 102
meillo@195 103 ls -ld /usr/local/sbin/masqmail /etc/masqmail /var/log/masqmail/ \
meillo@174 104 /var/run/masqmail /var/spool/masqmail/ /var/spool/masqmail/*
meillo@0 105
meillo@0 106 should give output similar to
meillo@0 107
meillo@165 108 -rwsr-xr-x 1 root root 399356 May 10 12:34 /usr/local/sbin/masqmail
meillo@59 109 drwxr-xr-x 2 root root 4096 May 10 12:34 /etc/masqmail
meillo@59 110 drwxr-xr-x 2 mail trusted 4096 May 10 12:34 /var/log/masqmail
meillo@59 111 drwxr-xr-x 2 mail trusted 4096 May 10 12:34 /var/run/masqmail
meillo@59 112 drwxr-xr-x 5 mail trusted 4096 May 10 12:34 /var/spool/masqmail
meillo@59 113 drwxr-xr-x 2 mail trusted 4096 May 10 12:34 /var/spool/masqmail/input
meillo@59 114 drwxr-xr-x 2 mail trusted 4096 May 10 12:34 /var/spool/masqmail/lock
meillo@0 115
meillo@165 116 Important are the set-user-id bit for /usr/local/sbin/masqmail and
meillo@165 117 the permissions of all files.
meillo@0 118
meillo@0 119
meillo@59 120
meillo@165 121 Making masqmail the default
meillo@165 122 ---------------------------
meillo@0 123
meillo@165 124 `sendmail' is the de-facto standard name of the system's MTA, no
meillo@165 125 matter which MTA actually runs. If you want to make masqmail the
meillo@185 126 system's MTA (i.e. replace sendmail, postfix, etc), make two symbolic
meillo@185 127 links:
meillo@0 128
meillo@165 129 ln -s /usr/local/sbin/masqmail /usr/lib/sendmail
meillo@185 130 ln -s /usr/local/sbin/masqmail /usr/sbin/sendmail
meillo@0 131
meillo@165 132 Now every mailer that used to call sendmail will now call masqmail.
meillo@165 133 If you already had an MTA installed and running, you can kill it and
meillo@165 134 start masqmail. Probably with:
meillo@59 135
meillo@165 136 /etc/init.d/sendmail restart
meillo@59 137
meillo@165 138 If this doesn't work as expected, you might need to add a special init
meillo@165 139 script for masqmail. Currently none is distributed with masqmail.
meillo@165 140 (Hopefully this will change soon.) Please ask on the mailing list for
meillo@165 141 help.
meillo@59 142
meillo@165 143 You can also directly start masqmail as daemon with:
meillo@59 144
meillo@165 145 /usr/local/sbin/masqmail -bd -q30m
meillo@59 146
meillo@59 147
meillo@59 148
meillo@165 149 Basic Configuration
meillo@165 150 -------------------
meillo@59 151
meillo@165 152 The only thing you must configure in order to use masqmail is the
meillo@165 153 hostname. It's the name under which masqmail operates. In most cases
meillo@165 154 it is the same as the machine's name, but it can be different.
meillo@59 155
meillo@165 156 The script `contrib/guess-hostname' tries to print the hostname of
meillo@165 157 your machine. The first output line is probably the best choice.
meillo@59 158
meillo@165 159 Create a minimal config with:
meillo@59 160
meillo@165 161 echo "host_name = HOSTNAME" >/etc/masqmail/masqmail.conf
meillo@59 162
meillo@165 163 (Substitute `HOSTNAME' with the real value, of course.)
meillo@59 164
meillo@165 165 Such a setup (i.e. the default one) does:
meillo@165 166 - deliver mail locally
meillo@206 167 - accept mail on stdin (plain text)
meillo@206 168 - accept mail on stdin (SMTP) (if started with -bs)
meillo@206 169 - accept mail on the local port 25 (SMTP) (if started with -bd)
meillo@185 170
meillo@165 171 It does not
meillo@185 172 - transfer mail to other machines
meillo@165 173 - accept mail from outside your machine
meillo@59 174
meillo@59 175
meillo@165 176 For more elaborate setups, have a look at docs/*setup and
meillo@165 177 docs/INSTALL*. You can also take the example configuration files in
meillo@165 178 examples/ as basis for your own. Take the man pages masqmail.conf(5)
meillo@165 179 and masqmail.route(5) for reference.
meillo@92 180
meillo@165 181 All configuration files should go into /etc/masqmail.
meillo@59 182
meillo@59 183
meillo@59 184
meillo@59 185 Written by oku.
meillo@165 186 Improved by meillo.